<div dir="ltr">Just caught it at the wrong time I guess. You are right though, usually a lot of support on these type of questions.<div><br></div><div>Brent</div></div><div class="gmail_extra"><br><div class="gmail_quote">On Thu, May 19, 2016 at 11:45 AM, Erik Halvorson <span dir="ltr"><<a href="mailto:hammer_down@hotmail.com" target="_blank">hammer_down@hotmail.com</a>></span> wrote:<br><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">
<div>
<div>On the RB26, there are no "corners" for the intake gaskets. Everything is either round, or heavily rounded corners. The Tomei install directions are brief to say the least, with no mention of the need for adding any sealant, so it seemed to point to
the logic of installing dry. All bolted up, just need to finish reinstalling all the ancillary equipment, refill coolant and fire her up.</div>
<div>My "no info here" jibe was more in surprise that I didn't get any replies. As a group, we usually have a terrific knowledge base of members.</div><span class="">
<div><br>
</div>
<div><br>
</div>
<div>
<div style="font-size:9px;color:#575757">Sent from my T-Mobile 4G LTE Device</div>
</div>
<br>
<br>
<div>-------- Original message --------</div>
</span><div><div class="h5"><div>From: Brent Meints <<a href="mailto:brent.meints@gmail.com" target="_blank">brent.meints@gmail.com</a>> </div>
<div>Date:05/19/2016 8:30 AM (GMT-08:00) </div>
<div>To: <a href="mailto:se-r@se-r-list.org" target="_blank">se-r@se-r-list.org</a> </div>
<div>Cc: </div>
<div>Subject: Re: Not SE-R specific: Polymer Coated Metal Intake Gasket Question </div>
<div><br>
</div>
<div>
<div dir="ltr">Sorry, I only woud put a dab of silicone in corners and transitions when using those style gaskets. I never ran a bead of RTV with them, no need.
<div><br>
</div>
<div>Brent Meints</div>
</div>
<div><br>
<div>On Thu, May 19, 2016 at 9:59 AM, Erik Halvorson <span dir="ltr">
<<a href="mailto:hammer_down@hotmail.com" target="_blank">hammer_down@hotmail.com</a>></span> wrote:<br>
<blockquote style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">
<div>
<div>No knowledge to be gained here it appears... I rolled the dice and installed it dry.</div>
<div><br>
</div>
<div><br>
</div>
<div>
<div style="font-size:9px;color:#575757">Sent from my T-Mobile 4G LTE Device</div>
</div>
<br>
<br>
<div>-------- Original message --------</div>
<div>From: Erik Halvorson <<a href="mailto:hammer_down@hotmail.com" target="_blank">hammer_down@hotmail.com</a>>
</div>
<div>Date:05/18/2016 9:25 AM (GMT-08:00) </div>
<div>To: se-r list <<a href="mailto:se-r@se-r-list.org" target="_blank">se-r@se-r-list.org</a>>
</div>
<div>Cc: </div>
<div>Subject: Not SE-R specific: Polymer Coated Metal Intake Gasket Question </div>
<div><br>
</div>
<div>
<div dir="ltr">
<div dir="ltr">I just had a quick question of which I was not able to find a quick answer via a Google search, so I figured I would go to the trusty ol' SE-R Mailing List of knowledgeable people. I am replacing leaking intake gaskets on an RB26 (OEM throttle
body and manifold gaskets blew out on Cylinder 6, which is common with oem gaskets when running more boost than stock). I decided I did not want to do this again until it was time to actually pull the engine out of the car, so I was going to install one of
the polymer coated metal gaskets currently available. They are touted as being virtually "blow out proof" if installed correctly. I am using the Tomei coated metal gaskets. There is no additional factory applied bead of RTV around the coolant ports like
you see on some traditional gaskets. These gaskets do come coated on both sides with a polymer for "superior sealing performance". They are stamped with a raised bead around each port (intake and water).<br>
<br>
The question is: <em>Do I need to put any sealant around the coolant ports for the manifold to cylinder head gasket or no sealant? </em></div>
<em></em> <br>
The directions from Tomei are more than a bit vague and they make no mention of adding any additional sealant for the coolant ports and yet it makes me hesitate to install the gasket "dry", mainly because I don't want to do this again. There is no room in
that engine bay for my large Scandinavian hands.....<br>
<div dir="ltr"><br>
Thanks in advance! <span><font color="#888888"><br>
<br>
Erik</font></span></div>
</div>
</div>
</div>
<br>
+----------------------------------------------------------------------+<br>
The mailing list home page is <a href="http://www.se-r-list.org/" rel="noreferrer" target="_blank">
http://www.se-r-list.org/</a><br>
To modify your subscription, go to <a href="http://www.se-r-list.org/mailman/listinfo/se-r" rel="noreferrer" target="_blank">
http://www.se-r-list.org/mailman/listinfo/se-r</a><br>
</blockquote>
</div>
<br>
<br clear="all">
<div><br>
</div>
-- <br>
<div>
<div dir="ltr">
<div>
<div dir="ltr">
<div>Regards,</div>
<div> </div>
<div>Brent Meints</div>
<div><br>
</div>
<div> </div>
</div>
</div>
</div>
</div>
</div>
</div>
</div></div></div>
</blockquote></div><br><br clear="all"><div><br></div>-- <br><div class="gmail_signature"><div dir="ltr"><div><div dir="ltr"><div>Regards,</div><div> </div><div>Brent Meints</div><div><br></div><div> </div></div></div></div></div>
</div>